SCHWINN BICYCLE SPEEDOMETER HURET 26" BIKE WHEEL SPEEDO HUB DRIVE 08
466USD $49.95
Condition : Used
Free Shipping
{{variant_type_name}} :
Notify me when the price drops
We will email you if we find a lower price on this product!
This is a clean and fully functional used example of a 26" Huret speedometer drive hub, Schwinn part number 08 466: a vintage speedo drive for 24" or 26" front wheels with bolt-on axles (not quick-release hub skewers), a nice short-arm example with black dust cap, repacked and in good working order. (In their original
26" speedo kits, Schwinn listed it as suitable for bikes with 24" wheels as well.)
Its drive ratio is 1:2.0. This drive is compatible with the chrome Schwinn Approved speedometers and drive cables (not included; see my other listings for examples of those), as well as Huret-branded bicycle speedometers. (It does not fit the large, round, 3"-diameter Stewart-Warner speedometers.)
I'm also including an accessory hardware kit, containing: One 5/16" axle bushing (silver) One 3/8" axle bushing (black) Four installation washers, to be used to clear either the inner face of the front fork or the axle cone nut, as needed (New) Foam dust ring seal (New) Plastic drive cable tie strap (New)
The two drive arms have a 3 1/8" (80mm) span, each extending 1 9/16" from the center of the axle hole, which is 7/16" diameter.
If using the plastic cable strap to secure the cable to the front fork, run it under very hot water first, so that it's pliable enough to get the head of the plastic locking pin through the hole in the strap. This drive is in clean used condition and full working order. I packed it with some fresh grease, and it turns smoothly. I am also including a free scanned reprint of an original Schwinn instruction sheet to help you get it all installed. NOTES: This is not for quick-release front hubs. This is only for bicycles with bolt-on front axles. This is not for Stewart-Warner speedometers. This is a Huret speedometer part. This auction is for the drive hub, bushing and washer kit only. If you do not see it in the photos, it is not included! Free Shipping is by domestic USPS Ground Advantage mail. See the Shipping and Handling section of this listing for all rates, including international Shipping charges. Please be sure you know the Shipping charge to your address before bidding. Import duties, taxes and charges are not included in the item price or shipping cost. You may need to pay these charges to your post office. (They are not charges from me.) These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Sorry, we do not understate package value, or mark it as a Gift. See my other listings for more vintage Schwinn speedometer items! Except where noted, combined shipping is available for all items ending on the same evening. Please do not copy any part of this listing without permission.
26" speedo kits, Schwinn listed it as suitable for bikes with 24" wheels as well.)
Its drive ratio is 1:2.0. This drive is compatible with the chrome Schwinn Approved speedometers and drive cables (not included; see my other listings for examples of those), as well as Huret-branded bicycle speedometers. (It does not fit the large, round, 3"-diameter Stewart-Warner speedometers.)
I'm also including an accessory hardware kit, containing: One 5/16" axle bushing (silver) One 3/8" axle bushing (black) Four installation washers,
The two drive arms have a 3 1/8" (80mm) span, each extending 1 9/16" from the center of the axle hole, which is 7/16" diameter.
If using the plastic cable strap to secure the cable to the front fork, run it under very hot water first, so that it's pliable enough to get the head of the plastic locking pin through the hole in the strap. This drive is in clean used condition and full working order. I packed it with some fresh grease, and it turns smoothly. I am also including a free scanned reprint of an original Schwinn instruction sheet to help you get it all installed. NOTES: This is not for quick-release front hubs. This is only for bicycles with bolt-on front axles. This is not for Stewart-Warner speedometers. This is a Huret speedometer part. This auction is for the drive hub, bushing and washer kit only. If you do not see it in the photos, it is not included! Free Shipping is by domestic USPS Ground Advantage mail. See the Shipping and Handling section of this listing for all rates, including international Shipping charges. Please be sure you know the Shipping charge to your address before bidding. Import duties, taxes and charges are not included in the item price or shipping cost. You may need to pay these charges to your post office. (They are not charges from me.) These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Sorry, we do not understate package value, or mark it as a Gift. See my other listings for more vintage Schwinn speedometer items! Except where noted, combined shipping is available for all items ending on the same evening. Please do not copy any part of this listing without permission.
Returns Accepted for this item if it's within 30 Days
Price type
IN STOCK
OUT STOCK
.
